// This configuration was automatically generated using the Online Configuration Generator // Authored by: Khalid Baheyeldin // Slewing Speed: 5.37 degrees/second (estimated) // Generated on: 2022-10-22 16:59 http://o.baheyeldin.com:1111/ // For more details visit: https://astrophoto.lionbit.com/3d-druck/26-keenone-eq // Version 1.1 - 12V-Stepper / 2,5°/sec // --------------------------------------------------------------------------------------------------------------------------------- // Configuration for OnStep /* * For more information on setting OnStep up see http://www.stellarjourney.com/index.php?r=site/equipment_onstep * and join the OnStep Groups.io at https://groups.io/g/onstep * * *** Read the compiler warnings and errors, they are there to help guard against invalid configurations *** */ // --------------------------------------------------------------------------------------------------------------------------------- // ADJUST THE FOLLOWING TO CONFIGURE YOUR CONTROLLER FEATURES ---------------------------------------------------------------------- // <-Req'd = always must set, <-Often = usually must set, Option = optional, Adjust = adjust as req'd, Infreq = infrequently changed // PINMAP ---------------------------------------------------------- see https://onstep.groups.io/g/main/wiki/6-Configuration#PINMAP // *** See the matching Pins.xxx.h file for your setup (found by looking in src/pinmaps/Models.h) with detailed information *** // *** to be sure it matches your wiring. *** USE AT YOUR OWN RISK *** *** // Parameter Name Value Default Notes Hint #define PINMAP CNC3 // OFF, Choose from: MiniPCB, MiniPCB2, MaxPCB, MaxPCB2, STM32Blue, <-Req'd // Ramps14, MaxESP2, MaxESP3. Check Constants.h for more info. // SERIAL PORT COMMAND CHANNELS ------------------------------------ see https://onstep.groups.io/g/main/wiki/6-Configuration#SERIAL #define SERIAL_A_BAUD_DEFAULT 9600 // 9600, n. Where n=9600,19200,57600,115200 (common baud rates.) Infreq #define SERIAL_B_BAUD_DEFAULT 9600 // 9600, n. See (src/HAL/) for your MCU Serial port # etc. Option #define SERIAL_B_ESP_FLASHING OFF // OFF, ON Upload ESP8266 WiFi firmware through SERIAL_B with :ESPFLASH# cmd. Option #define SERIAL_C_BAUD_DEFAULT ON // OFF, n, ON for ESP32 Bluetooth. Option #define SERIAL_C_BLUETOOTH_NAME "KeenOne" // "On..", Bluetooth device name for ESP32. Option // MOUNT TYPE -------------------------------------------------- see https://onstep.groups.io/g/main/wiki/6-Configuration#MOUNT_TYPE #define MOUNT_TYPE GEM // GEM, GEM for German Equatorial, FORK for Equatorial Fork, or ALTAZM <-Req'd // Dobsonian etc. mounts. GEM Eq mounts perform meridian flips. // USER FEEDBACK -------------------------------------------- see https://onstep.groups.io/g/main/wiki/6-Configuration#USER_FEEDBACK #define LED_STATUS ON // ON, Blinks w/sidereal tracking otherwise steady on indicates activity. Option #define LED_STATUS2 OFF // OFF, ON Blinks 1s interval w/PPS sync, steady for gotos, off if in standby. Option #define LED_RETICLE OFF // OFF, n. Where n=0..255 (0..100%) activates feature sets default brightness. Option #define BUZZER OFF // OFF, ON, n. Where n=100..6000 (Hz freq.) for piezo speaker. ON for buzzer. Option #define BUZZER_STATE_DEFAULT ON // OFF, ON Start with piezo buzzer/speaker enabled. Option // TIME AND LOCATION -------------------------------------------------- see https://onstep.groups.io/g/main/wiki/6-Configuration#TLS #define TIME_LOCATION_SOURCE OFF // OFF, DS3231 (I2c,) DS3234 (Spi,) TEENSY (T3.2 internal,) or GPS source. Option // Provides Date/Time, and if available, PPS & Lat/Long also. // // SENSORS -------------------------------------------------------- see https://onstep.groups.io/g/main/wiki/6-Configuration#SENSORS // * = also supports ON_PULLUP or ON_PULLDOWN to activate MCU internal resistors if present. #define WEATHER OFF // OFF, BME280 (I2C 0x77,) BME280_0x76, BME280_SPI (see pinmap for CS.) Option // BMP280 (I2C 0x77,) BMP280_0x76, BMP280_SPI (see pinmap for CS.) // BME280 or BMP280 for temperature, pressure. BME280 for humidity also. #define TELESCOPE_TEMPERATURE OFF // OFF, DS1820, n. Where n is the DS1820 s/n for focuser temperature. Adjust #define HOME_SENSE OFF // OFF, ON*. Automatically detect and use home switches. For GEM mode only. Option #define HOME_SENSE_STATE_AXIS1 HIGH // HIGH, State when clockwise of home position, as seen from front. Rev. w/LOW. Adjust #define HOME_SENSE_STATE_AXIS2 HIGH // HIGH, State when clockwise of home position, as seen from above. Rev. w/LOW. Adjust // Signal state reverses when travel moves ccw past the home position. #define LIMIT_SENSE OFF // OFF, ON* limit sense switch close to Gnd stops gotos and/or tracking. Option #define LIMIT_SENSE_STATE LOW // LOW, For NO (normally open) switches, HIGH for NC (normally closed.) Adjust #define PEC_SENSE OFF // OFF, ON*, n, sense digital OR n=0 to 1023 (0 to 3.3V or 5V) analog threshold. Option #define PEC_SENSE_STATE HIGH // HIGH, Senses the PEC signal rising edge or use LOW for falling edge. Adjust // Ignored in ALTAZM mode. #define PPS_SENSE OFF // OFF, ON* enables PPS (pulse per second,) senses signal rising edge. Option // Better tracking accuracy especially for Mega2560's w/ceramic resonator. // ST4 INTERFACE ------------------------------------------------------ see https://onstep.groups.io/g/main/wiki/6-Configuration#ST4 // *** It is up to you to verify the interface meets the electrical specifications of any connected device, use at your own risk *** #define ST4_INTERFACE OFF // OFF, ON, ON_PULLUP enables interface. <= 1X guides unless hand control mode. Option // During goto btn press: aborts slew or continue meridian flip pause home #define ST4_HAND_CONTROL OFF // OFF, ON for hand controller special features and SHC support. Option // Hold [E]+[W] btns >2s: Guide rate [E]- [W]+ [N] trk on/off [S] sync // Hold [N]+[S] btns >2s: Usr cat item [E]- [W]+ [N] goto [S] snd on/off #define ST4_HAND_CONTROL_FOCUSER OFF // OFF, ON alternate to above: Focuser move [E]f1 [W]f2 [N]- [S]+ Option // GUIDING BEHAVIOUR ---------------------------------------------- see https://onstep.groups.io/g/main/wiki/6-Configuration#GUIDING #define GUIDE_TIME_LIMIT 0 // 0, No guide time limit. Or n. Where n=1..120 second time limit guard. Adjust #define GUIDE_DISABLE_BACKLASH OFF // OFF, Disable backlash takeup during guiding at <= 1X Option // TRACKING BEHAVIOUR -------------------------------------------- see https://onstep.groups.io/g/main/wiki/6-Configuration#TRACKING #define TRACK_AUTOSTART ON // OFF, ON Start with tracking enabled. Option #define TRACK_REFRACTION_RATE_DEFAULT OFF // OFF, ON Start w/atmospheric refract. compensation (RA axis/Eq mounts only.) Option #define TRACK_BACKLASH_RATE 25 // 25, n. Where n=2..50 (x sidereal rate) during backlash takeup. Option // Too fast motors stall/gears slam or too slow and sluggish in backlash. // SLEWING BEHAVIOUR ---------------------------------------------- see https://onstep.groups.io/g/main/wiki/6-Configuration#SLEWING #define SLEW_RATE_BASE_DESIRED 2.5 // 1.0, n. Desired slew rate in deg/sec. Adjustable at run-time from <-Req'd // 1/2 to 2x this rate, and as MCU performace considerations require. #define SLEW_RATE_MEMORY OFF // OFF, ON Remembers rates set across power cycles. Option #define SLEW_ACCELERATION_DIST 3.0 // 5.0, n, (degrees.) Approx. distance for acceleration (and deceleration.) Adjust #define SLEW_RAPID_STOP_DIST 1.5 // 2.0, n, (degrees.) Approx. distance required to stop when a slew Adjust // is aborted or a limit is exceeded. // PIER SIDE BEHAVIOUR -------------------------------------------- see https://onstep.groups.io/g/main/wiki/6-Configuration#SYNCING #define MFLIP_SKIP_HOME ON // OFF, ON Goto directly to the destination without visiting home position. Option #define MFLIP_PAUSE_HOME_MEMORY OFF // OFF, ON Remember meridian flip pause at home setting across power cycles. Option #define MFLIP_AUTOMATIC_MEMORY ON // OFF, ON Remember automatic meridian flip setting across power cycles. Option #define PIER_SIDE_SYNC_CHANGE_SIDES OFF // OFF, ON Allows sync to change pier side, for GEM mounts. Option #define PIER_SIDE_PREFERRED_DEFAULT BEST // BEST, Stays on current side if possible. EAST or WEST switch if possible. Option // PARKING BEHAVIOUR ---------------------------------------------- see https://onstep.groups.io/g/main/wiki/6-Configuration#PARKING #define STRICT_PARKING OFF // OFF, ON Un-parking is only allowed if successfully parked. Option // MOTION CONTROL -------------------------------------------------- see https://onstep.groups.io/g/main/wiki/6-Configuration#MOTION #define STEP_WAVE_FORM PULSE // SQUARE, PULSE Step signal wave form faster rates. SQUARE best signal integrity. Adjust // Stepper driver models (also see ~/OnStep/src/sd_drivers/Models.h for additional infrequently used models and more info.): // A4988, DRV8825, LV8729, S109, SSS TMC2209*, TMC2130* **, and TMC5160* *** // * = add _QUIET (stealthChop tracking) for example "TMC2130_QUIET" // ** = SSS TMC2130 if you choose to set stepper driver current (in mA) set Vref pot. 2.5V instead of by motor current as usual. // *** = SSS TMC5160 you must set stepper driver current (in mA) w/ #define AXISn_TMC_IRUN (IHOLD, etc.) // AXIS1 RA/AZM // see https://onstep.groups.io/g/main/wiki/6-Configuration#AXIS1 #define AXIS1_STEPS_PER_DEGREE 18854.666666666668 // 12800, n. Number of steps per degree: <-Req'd // n = (stepper_steps * micro_steps * overall_gear_reduction)/360.0 #define AXIS1_STEPS_PER_WORMROT 85920 // 12800, n. Number of steps per worm rotation (PEC Eq mode only:) <-Req'd // n = (AXIS1_STEPS_PER_DEGREE*360)/reduction_final_stage #define AXIS1_DRIVER_MODEL TMC2130_QUIET // OFF, (See above.) Stepper driver model. <-Often #define AXIS1_DRIVER_MICROSTEPS 16 // OFF, n. Microstep mode when tracking. <-Often #define AXIS1_DRIVER_MICROSTEPS_GOTO OFF // OFF, n. Microstep mode used during gotos. Option #define AXIS1_DRIVER_IHOLD 10 // OFF, n, (mA.) Current during standstill. OFF uses IRUN/2.0 Option #define AXIS1_DRIVER_IRUN 70 // OFF, n, (mA.) Current during tracking, appropriate for stepper/driver/etc. Option #define AXIS1_DRIVER_IGOTO 600 // OFF, n, (mA.) Current during slews. OFF uses same as IRUN. Option #define AXIS1_DRIVER_REVERSE OFF // OFF, ON Reverses movement direction, or reverse wiring instead to correct. <-Often #define AXIS1_DRIVER_STATUS TMC_SPI // OFF, TMC_SPI, HIGH, or LOW. Polling for driver status info/fault detection. Option #define AXIS1_LIMIT_MIN -180 // -180, n. Where n= -90..-270 (degrees.) Minimum "Hour Angle" for Eq modes. Adjust // n. Where n=-180..-360 (degrees.) Minimum Azimuth for AltAzm mode. #define AXIS1_LIMIT_MAX 180 // 180, n. Where n= 90.. 270 (degrees.) Maximum "Hour Angle" for Eq modes. Adjust // n. Where n= 180.. 360 (degrees.) Maximum Azimuth for AltAzm mode. #define AXIS1_HOME_DEFAULT 90 // 90 (GEM) or 0 (for FORK or ALTAZM) This is the default home position at startup. // AXIS2 DEC/ALT // see https://onstep.groups.io/g/main/wiki/6-Configuration#AXIS2 #define AXIS2_STEPS_PER_DEGREE 18854.666666666668 // 12800, n. Number of steps per degree: <-Req'd // n = (stepper_steps * micro_steps * overall_gear_reduction)/360.0 #define AXIS2_DRIVER_MODEL TMC2130_QUIET // OFF, (See above.) Stepper driver model. <-Often #define AXIS2_DRIVER_MICROSTEPS 16 // OFF, n. Microstep mode when tracking. <-Often #define AXIS2_DRIVER_MICROSTEPS_GOTO OFF // OFF, n. Microstep mode used during gotos. Option #define AXIS2_DRIVER_IHOLD 10 // OFF, n, (mA.) Current during standstill. OFF uses IRUN/2.0 Option #define AXIS2_DRIVER_IRUN 70 // OFF, n, (mA.) Current during tracking, appropriate for stepper/driver/etc. Option #define AXIS2_DRIVER_IGOTO 600 // OFF, n, (mA.) Current during slews. OFF uses same as IRUN. Option #define AXIS2_DRIVER_POWER_DOWN OFF // OFF, ON Powers off 10sec after movement stops or 10min after last<=1x guide. Option #define AXIS2_DRIVER_REVERSE ON // OFF, ON Reverses movement direction, or reverse wiring instead to correct. <-Often #define AXIS2_DRIVER_STATUS TMC_SPI // OFF, TMC_SPI, HIGH, or LOW. Polling for driver status info/fault detection. Option #define AXIS2_TANGENT_ARM OFF // OFF, ON +limit range below. Set cntr w/[Reset Home] Return cntr w/[Find Home] Infreq #define AXIS2_LIMIT_MIN -90 // -90, n. Where n=-90..0 (degrees.) Minimum allowed declination. Infreq #define AXIS2_LIMIT_MAX 90 // 90, n. Where n=0..90 (degrees.) Maximum allowed declination. Infreq #define AXIS2_HOME_DEFAULT 90 // 90 (GEM) or 0 (for FORK or ALTAZM) This is the default home position at startup. // AXIS3 ROTATOR // see https://onstep.groups.io/g/main/wiki/6-Configuration#AXIS3 #define ROTATOR OFF // OFF, ON to enable the rotator (or de-rotator for ALTAZM mounts.) Option #define AXIS3_STEPS_PER_DEGREE 64.0 // 64.0, n. Number of steps per degree for rotator/de-rotator. Adjust // Alt/Az de-rotation: n = (num_circumference_pixels * 2)/360, minimum #define AXIS3_SLEW_RATE_DESIRED 1.0 // 1.0, n, (degrees/second) Maximum speed depends on processor. Adjust #define AXIS3_DRIVER_MODEL OFF // OFF, TMC2130, TMC5160. Leave OFF for all drivers models except these. Option #define AXIS3_DRIVER_MICROSTEPS OFF // OFF, n. Microstep mode when tracking. For TMC2130, TMC5160. Option #define AXIS3_DRIVER_IHOLD OFF // OFF, n, (mA.) Current standstill. OFF uses IRUN/2.0. " Option #define AXIS3_DRIVER_IRUN OFF // OFF, n, (mA.) Current tracking, appropriate for stepper/driver/etc. " Option #define AXIS3_DRIVER_POWER_DOWN OFF // OFF, ON Powers off the motor at stand-still. Option #define AXIS3_DRIVER_REVERSE OFF // OFF, ON Reverses movement direction, or reverse wiring instead to correct. Option #define AXIS3_LIMIT_MIN -180 // -180, n. Where n=-360..0 (degrees.) Minimum allowed rotator angle. Infreq #define AXIS3_LIMIT_MAX 180 // 180, n. Where n=0..360 (degrees.) Maximum allowed rotator angle. Infreq // AXIS4 FOCUSER 1 // see https://onstep.groups.io/g/main/wiki/6-Configuration#AXIS4 #define FOCUSER1 ON // OFF, ON to enable this focuser. Option #define AXIS4_STEPS_PER_MICRON 5.0 // 0.5, n. Steps per micrometer. Figure this out by testing or other means. Adjust #define AXIS4_SLEW_RATE_DESIRED 1000 // 500, n, Where n=200..5000 (um/s.) Max microns/second. In DC mode, max pwr % Adjust #define AXIS4_DRIVER_MODEL OFF // OFF, TMC2130, TMC5160. Leave OFF for all drivers models except these. Option #define AXIS4_DRIVER_MICROSTEPS 16 // OFF, n. Microstep mode when tracking. For TMC2130, TMC5160. Option #define AXIS4_DRIVER_IHOLD OFF // OFF, n, (mA.) Current standstill. OFF uses IRUN/2.0. " Option #define AXIS4_DRIVER_IRUN OFF // OFF, n, (mA.) Current tracking, appropriate for stepper/driver/etc. " Option #define AXIS4_DRIVER_POWER_DOWN OFF // OFF, ON Powers off the motor at stand-still. Option #define AXIS4_DRIVER_REVERSE OFF // OFF, ON Reverses movement direction, or reverse wiring instead to correct. Option #define AXIS4_DRIVER_DC_MODE OFF // OFF, DRV8825 for pwm dc motor control on stepper driver outputs. Option #define AXIS4_LIMIT_MIN_RATE 50 // 50, n. Where n=1..1000 (um/s.) Minimum microns/second. In DC mode, min pwr. Adjust #define AXIS4_LIMIT_MIN 0 // 0, n. Where n=0..500 (millimeters.) Minimum allowed position. Adjust #define AXIS4_LIMIT_MAX 40 // 50, n. Where n=0..500 (millimeters.) Maximum allowed position. Adjust // AXIS5 FOCUSER 2 // see https://onstep.groups.io/g/main/wiki/6-Configuration#AXIS5 #define FOCUSER2 OFF // OFF, ON to enable this focuser. Option #define AXIS5_STEPS_PER_MICRON 0.5 // 0.5, n. Steps per micrometer. Figure this out by testing or other means. Adjust #define AXIS5_SLEW_RATE_DESIRED 500 // 500, n, Where n=200..5000 (um/s.) Max microns/second. In DC mode, max pwr % Adjust #define AXIS5_DRIVER_MODEL OFF // OFF, TMC2130, TMC5160. Leave OFF for all drivers models except these. Option #define AXIS5_DRIVER_MICROSTEPS OFF // OFF, n. Microstep mode when tracking. For TMC2130, TMC5160. Option #define AXIS5_DRIVER_IHOLD OFF // OFF, n, (mA.) Current standstill. OFF uses IRUN/2.0. " Option #define AXIS5_DRIVER_IRUN OFF // OFF, n, (mA.) Current tracking, appropriate for stepper/driver/etc. " Option #define AXIS5_DRIVER_POWER_DOWN OFF // OFF, ON Powers off the motor at stand-still. Option #define AXIS5_DRIVER_REVERSE OFF // OFF, ON Reverses movement direction, or reverse wiring instead to correct. Option #define AXIS5_DRIVER_DC_MODE OFF // OFF, DRV8825 for pwm dc motor control on stepper driver outputs. Option #define AXIS5_LIMIT_MIN_RATE 50 // 50, n. Where n=1..1000 (um/s.) Minimum microns/second. In DC mode, min pwr. Adjust #define AXIS5_LIMIT_MIN 0 // 0, n. Where n=0..500 (millimeters.) Minimum allowed position. Adjust #define AXIS5_LIMIT_MAX 50 // 50, n. Where n=0..500 (millimeters.) Maximum allowed position. Adjust // AUXILIARY FEATURE CONTROL ------------------------------ see https://onstep.groups.io/g/main/wiki/6-ConfigurationMaster#AUXILIARY #define FEATURE_LIST_DS ON // OFF, temporarily set ON to list ds18b20 and ds2413 device serial numbers. Adjust #define FEATURE1_NAME "INTERVALOMETER" // "FE..", Name of feature being controlled. Adjust #define FEATURE1_PURPOSE INTERVALOMETER // OFF, SWITCH, ANALOG_OUT, DEW_HEATER, INTERVALOMETER. Option #define FEATURE1_TEMP OFF // OFF, DS1820, n. Where n is the ds18b20 s/n for DEW_HEATER temperature. Adjust #define FEATURE1_PIN AUX // OFF, AUX, DS2413, n. Where n is ds2413 s/n (gpio0) or n=0 to 255 (pin#.) Adjust #define FEATURE1_DEFAULT_VALUE OFF // OFF, ON, n. Where n=0..255 for ANALOG_OUT purpose. Adjust #define FEATURE2_NAME "FEATURE2" // "FE..", Name of feature being controlled. Adjust #define FEATURE2_PURPOSE OFF // OFF, SWITCH, ANALOG_OUT, DEW_HEATER, INTERVALOMETER. Option #define FEATURE2_TEMP OFF // OFF, DS1820, n. Where n is the ds18b20 s/n for DEW_HEATER temperature. Adjust #define FEATURE2_PIN OFF // OFF, AUX, CHAIN (ds2413 gpio1,) n. Where n=0 to 255 (pin#.) Adjust #define FEATURE2_DEFAULT_VALUE OFF // OFF, ON, n. Where n=0..255 for ANALOG_OUT purpose. Adjust #define FEATURE3_NAME "FEATURE3" // "FE..", Name of feature being controlled. Adjust #define FEATURE3_PURPOSE OFF // OFF, SWITCH, ANALOG_OUT, DEW_HEATER, INTERVALOMETER. Option #define FEATURE3_TEMP OFF // OFF, DS1820, n. Where n is the ds18b20 s/n for DEW_HEATER temperature. Adjust #define FEATURE3_PIN OFF // OFF, AUX, DS2413, n. Where n is ds2413 s/n (gpio0) or n=0 to 255 (pin#.) Adjust #define FEATURE3_DEFAULT_VALUE OFF // OFF, ON, n. Where n=0..255 for ANALOG_OUT purpose. Adjust #define FEATURE4_NAME "FEATURE4" // "FE..", Name of feature being controlled. Adjust #define FEATURE4_PURPOSE OFF // OFF, SWITCH, ANALOG_OUT, DEW_HEATER, INTERVALOMETER. Option #define FEATURE4_TEMP OFF // OFF, DS1820, n. Where n is the ds18b20 s/n for DEW_HEATER temperature. Adjust #define FEATURE4_PIN OFF // OFF, AUX, CHAIN (ds2413 gpio1,) n. Where n=0 to 255 (pin#.) Adjust #define FEATURE4_DEFAULT_VALUE OFF // OFF, ON, n. Where n=0..255 for ANALOG_OUT purpose. Adjust #define FEATURE5_NAME "FEATURE5" // "FE..", Name of feature being controlled. Adjust #define FEATURE5_PURPOSE OFF // OFF, SWITCH, ANALOG_OUT, DEW_HEATER, INTERVALOMETER. Option #define FEATURE5_TEMP OFF // OFF, DS1820, n. Where n is the ds18b20 s/n for DEW_HEATER temperature. Adjust #define FEATURE5_PIN OFF // OFF, AUX, DS2413, n. Where n is ds2413 s/n (gpio0) or n=0 to 255 (pin#.) Adjust #define FEATURE5_DEFAULT_VALUE OFF // OFF, ON, n. Where n=0..255 for ANALOG_OUT purpose. Adjust #define FEATURE6_NAME "FEATURE6" // "FE..", Name of feature being controlled. Adjust #define FEATURE6_PURPOSE OFF // OFF, SWITCH, ANALOG_OUT, DEW_HEATER, INTERVALOMETER. Option #define FEATURE6_TEMP OFF // OFF, DS1820, n. Where n is the ds18b20 s/n for DEW_HEATER temperature. Adjust #define FEATURE6_PIN OFF // OFF, AUX, CHAIN (ds2413 gpio1,) n. Where n=0 to 255 (pin#.) Adjust #define FEATURE6_DEFAULT_VALUE OFF // OFF, ON, n. Where n=0..255 for ANALOG_OUT purpose. Adjust #define FEATURE7_NAME "FEATURE7" // "FE..", Name of feature being controlled. Adjust #define FEATURE7_PURPOSE OFF // OFF, SWITCH, ANALOG_OUT, DEW_HEATER, INTERVALOMETER. Option #define FEATURE7_TEMP OFF // OFF, DS1820, n. Where n is the ds18b20 s/n for DEW_HEATER temperature. Adjust #define FEATURE7_PIN OFF // OFF, AUX, DS2413, n. Where n is ds2413 s/n (gpio0) or n=0 to 255 (pin#.) Adjust #define FEATURE7_DEFAULT_VALUE OFF // OFF, ON, n. Where n=0..255 for ANALOG_OUT purpose. Adjust #define FEATURE8_NAME "FEATURE8" // "FE..", Name of feature being controlled. Adjust #define FEATURE8_PURPOSE OFF // OFF, SWITCH, ANALOG_OUT, DEW_HEATER, INTERVALOMETER. Option #define FEATURE8_TEMP OFF // OFF, DS1820, n. Where n is the ds18b20 s/n for DEW_HEATER temperature. Adjust #define FEATURE8_PIN OFF // OFF, AUX, CHAIN (ds2413 gpio1,) n. Where n=0 to 255 (pin#.) Adjust #define FEATURE8_DEFAULT_VALUE OFF // OFF, ON, n. Where n=0..255 for ANALOG_OUT purpose. Adjust // THAT'S IT FOR USER CONFIGURATION! // ------------------------------------------------------------------------------------------------------------------------- #define FileVersionConfig 4